What're your beliefs on Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't precisely rocket science, however it does need strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old tub with a new one is also a moderately tough job. If the old tub is easily obtainable, the project can relocate speedily; if you have to open a wall surface to get rid of the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to leave the old bathtub as well as embeded in the brand-new one. Ensure you have actually qualified yourself for the task and also fit attempting it. As opposed to employing a specialist to take control of a halfway-completed project, it is better to take into consideration using one prior to you start. Chances are you might need an expert plumber to make tube links.
This write-up will aid you set up a brand-new bath tub in your bathroom if you have actually currently bought a brand-new tub and don't require to change the setup of your previous water pipes.
Your devices as well as product checklist must make up the following:
Planning for the Installment
Firstly, the sustaining frame supplied with the bath must be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to avoid stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently be ready to be suited its last placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of removing the existing faucets can be quite bothersome because of the limited access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the remaining water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Making use of both wood boards under its feet, put the bath tub in the needed placement. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the bath tub until the level reviews level.
To mount taps, fit all-time low of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the water supply and inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bathtub and likewise check the overflow outlet and also the normal electrical outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and sealing around the tub needs to wait until the bath tub has been utilized a minimum of when as this will resolve it right into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in place between the faucet as well as the sink. Secure the tap in position with the producer given backnut. When the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The former type ought to be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in problems with wetness as well as feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, and also can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the market. It is recommended to fit the floor tiles utilizing waterproof or water-proof adhesive and also grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
As a keen reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that information was a good idea. Sharing is caring. You won't know, you could be doing someone a favor. We take joy in reading our article about A Step-by-Step Guide to Installing a Bathtub.
Book An Appointment